Flow Max RV Fresh Water Pump - 115 Volt - 3.3 Gallons Per Minute - 45 PSI
Motorized, self-priming pump creates a consistent flow of fresh water to your RV or camper. Works as a direct replacement for a 115-volt pump. The quiet pump has a check valve to prevent backflow and a thermal breaker to prevent overheating.
Features:
- Motorized water pump provides a consistent flow of fresh water to your RV or camper
- Can be used as a direct replacement for any OEM RV or marine pump
- Self-priming design eliminates air binding by removing air from the pipeline
- Unit is capable of up to 6' vertical prime and 30' horizontal prime
- Heavy-duty, corrosion-resistant motor has ball bearings for a long life
- Provides quiet, disturbance-free operation
- Can run dry without causing damage
- Integrated thermal breaker protects the motor from overheating
- Breaker automatically resets when temperature drops
- Internal check valve prevents backflow contamination of your clean water supply
- Included strainer stops bugs and debris from entering the pump
- Feet are flexible to reduce excessive vibration and noise
- Enclosed housing with sealed switches blocks moisture from getting in
- Electrocoating finish resists the effects of rain and other elements
- Bolt-on installation in any position
- Hardware not included
- 1/2" Diameter hose fitting at inlet and outlet ports
- Features a tapered seal for a watertight connection
- Includes 2 swivel, high-pressure fittings
- 3-Wire configuration
- Black for live (hotwire)
- White for neutral
- Green and yellow for ground
- 15 Amp switch and a 10 amp fuse (not included) are required
- Freeze and thaw tested up to 5 cycles of 2 hours
- NSF and CSA certified
Specs:
- Overall dimensions: 8-3/4" long x 5-1/4" wide x 5" tall
- Mounting base dimensions: 3-3/4" long x 4-1/4" wide
- Voltage: 115 volts AC
- Maximum power draw: 1 amp
- Flow: 3.3 gallons per minute
- Pressure setting: 45 psi
- Runtime: 5 minutes on/10 minutes off
- Maximum water temperature: 140 degrees F (60 degrees C)
- 2-Year limited warranty
Notes:
- Designed for intermittent use only - continuous running under higher pressures may reduce pump life.
- Pump should not be used for running a Reverse-Osmosis (RO) Filtration System.
Self-Priming Water Pump
This motorized pump can be used as a direct replacement for any OEM RV or marine pump and lets you supply a smooth, consistent flow to the fresh water system in your RV, camper, or boat. The diaphragm-style pump has a self-priming design. The sealed, flexible diaphragm creates a vacuum that draws in the water, allowing the pump to self-prime. This design eliminates air pockets in the pipeline - also known as air binding - for a steady, uninterrupted stream of water to your faucet or other fresh water source. It has the ability to prime up to 6' vertically and 30' horizontally. The pump also features an internal check valve that prevents backflow contamination of your clean water supply.
The pump has been thoroughly freeze and thaw tested for up to 5 two-hour cycles, and it was tested with a higher pressure at shutoff than other water pumps.
Heavy-Duty Motor
The heavy-duty motor operates quietly without any disturbances and features ball bearings that enable it to have a long life. It doesn't have a rotating seal that will burn up, allowing it the ability to run dry without causing any damage.
The motor also has an integrated thermal breaker that interrupts operation when the motor becomes too hot in order to protect it from overheating. When the temperature of the motor drops, the breaker automatically resets.
Water-Resistant Design
This enclosed, water-resistant pump has sealed switches that keep moisture from getting in. The electrocoating finish withstands the effects of rain, snow, and other elements, preventing rust and ensuring long-lasting durability.
Installation
This water pump can be bolted down in multiple locations and positions. It can be installed above, below, or at the same level as the water tank, as long as the location is dry and easily accessible for maintenance. Mounting hardware is not included.
Once the pump is bolted down, insert the strainer on the inlet side. This strainer prevents bugs and debris from entering the pump. Then with the included swivel fittings, attach high-pressure hoses to the strainer and the outlet port for a tapered, watertight seal.
Finally, make your wire connections. The black wire is your live (or hotwire), the white wire is your neutral, and the green and yellow wire is your ground. Please note that a 15 amp switch and a 10 amp fuse (not included) are required.
